1. New to Christmas lighting? Get started with the AusChristmasLighting 101 Manual:
    auschristmaslighting.com/wiki/AusChristmasLighting-101

Setup of the F16v3

Discussion in 'Show Off Arena' started by Bryan H, Jun 29, 2017.

  1. Bryan H

    Bryan H Bryan H Generous Elf

    Joined:
    Feb 15, 2017
    Messages:
    143
    Likes Received:
    37
    Location:
    Tumut
    Hi, Guys, I will start this thread. I would like to see photos of how others are putting their F16v3 together. This is my setup which took me about 6 hours to build so far. I am yet to run the pigtails which I will do over the next week or two. The cabinet is lockable and will need an air vent for airflow.
     

    Attached Files:

    NTKing(Brad) likes this.
  2. OzAz

    OzAz Senior Elf Generous Elf

    Joined:
    Dec 29, 2015
    Messages:
    528
    Likes Received:
    156
    Location:
    Newcastle
    you may have to wait till next year to see mine.
    looking good @hammo131 nice use of spiralwrap, just wondering where the pigtails will all fit?
     
  3. Heath-LightsOnTapley

    Heath-LightsOnTapley Senior Elf Generous Elf

    Joined:
    Aug 23, 2015
    Messages:
    599
    Likes Received:
    66
    Location:
    sheidow park
    got any photos of underneath the boards hammo?
     
  4. darylc

    darylc 404 darylc not found Global Moderator Generous Elf

    Joined:
    Dec 8, 2012
    Messages:
    478
    Likes Received:
    109
    @hammo131 - watch out for that red expansion board, I don't believe that will work. From what I hear, it might be possible to use with a slight mod - removing one of the pins but I've not seen those specific instructions be released yet.
     
  5. OP
    OP
    Bryan H

    Bryan H Bryan H Generous Elf

    Joined:
    Feb 15, 2017
    Messages:
    143
    Likes Received:
    37
    Location:
    Tumut
    Well, I am hoping they will come out the side...
     
  6. OP
    OP
    Bryan H

    Bryan H Bryan H Generous Elf

    Joined:
    Feb 15, 2017
    Messages:
    143
    Likes Received:
    37
    Location:
    Tumut
    Ok, looking at their manual it should work, but I have never used a falcon before. If that is the case, I should have got the 2nd board from you...
     
  7. OP
    OP
    Bryan H

    Bryan H Bryan H Generous Elf

    Joined:
    Feb 15, 2017
    Messages:
    143
    Likes Received:
    37
    Location:
    Tumut
    I thought I had one, will just pop up to the shed and take a photo...
     
  8. OP
    OP
    Bryan H

    Bryan H Bryan H Generous Elf

    Joined:
    Feb 15, 2017
    Messages:
    143
    Likes Received:
    37
    Location:
    Tumut
    Photos of under the boards
     

    Attached Files:

  9. burnt

    burnt Apprentice Elf Generous Elf

    Joined:
    Nov 17, 2014
    Messages:
    73
    Likes Received:
    35
    look like the psu come out easy
     
  10. videoman3857

    videoman3857 Full Time Elf

    Joined:
    Apr 21, 2016
    Messages:
    362
    Likes Received:
    84
    Location:
    Glass House Mountains
    Heat is thy enemy !
    Need more than "a" vent
    With 6 x PSU I would be looking at Fan assisted cross flow ventilation
    Air sucked in, Hot air blown out.
     

Share This Page