Recent content by John_82

  1. J

    push to light up selfie wings

    Would be interesting to see how they look at night and with someone in front of them taking a photo, assuming they would have to use a flash to see little Jenny? how will the pixel colours turn out in the photo?
  2. J

    Bunnings enclosure - Ezy Storage Waterproof IP67 Storage Box - 18L

    Nice! I’m using the same box but the slightly bigger 32L model. I went the bigger box because I’ve gone horizontal rather than vertical with my boards and power.
  3. J

    HE123-RX Receiver

    Awesome, thank you! Just wanted to check if it was anything to worry about
  4. J

    HE123-RX Receiver

    Thanks, I’m still. A little confused I have three of these boards connected to different 12v power supply’s, two of them show green LED indicator on LD1 and one of them shows a Orange LED on R10? I haven’t connected any lights to the one that shows R10, is this something I need to worry about ?
  5. J

    HE123-RX Receiver

    @AAH are you able to tell me what the R10 vs LD1 indicator lights mean? I had a look through the HE123 manual on the website but it just says “power led” (or maybe I missed it)
  6. J

    xLights sharing: sequences

    So I have been searching and not sure if I have overlooked it or not... But has any one shared anything from the Wiggles?
  7. J

    First year show - Struggling to build a shopping cart

    For your power injection t’s make sure you have the right connector for the 2 core’s on your extension leads (From F8 distro to the 3-2-3 splitter) I made the mistake thinking my 3-2-3 splitter had xconnect on all connections, only the 3 pin connectors were xconnect and the 2 pin were different...
  8. J

    First year show - Struggling to build a shopping cart

    Looks like a good plan Remember though with new receivers you’ll need to build more boxes that include the following and these are off the top of my head: 1. PSU 2. cases 3. cable glands 4. If you have the board mounted on something then motherboard standoffs, m4? screws 5. Fuse holders 6...
  9. J

    First year show - Struggling to build a shopping cart

    I think this is right V3 you needed an expansion board V4 comes with two ports for differential receivers But remember you may not need these, only if your runs aren’t quite long from the controller. It you have a central point for the controller that can reach all the runs using a null pixel...
  10. J

    First year show - Struggling to build a shopping cart

    Hi Joshaaye, I’m new to the hobby also and just today jsunk $750 on 2000 pixels from my tax return too 😂 Questions I have about your setup I see you are using the falcon controller? have you ordered a smart or differential receiver also? (I didn’t see on your shopping list) If you are...
  11. J

    HE123-RX Receiver

    Just an FYI, I can confirm the HE123-RX receiver works as a standard differential receiver with the Kulp K8-PB boards. Great option for an inexpensive receiver
  12. J

    HE123-RX Receiver

    Thanks, I’ll order one and test and if all good order a couple more
  13. J

    HE123-RX Receiver

    Hi all, I have a question around the compatibility of the Kulp K8-PB and the Hansen HE123-RX differential receiver. The Kulp boards support both smart and differential receivers. The Kulp Manual states: “Each RJ45 port can connect to one Differential Receiver or up to 3 daisy- chained...
  14. J

    New from Brisbane!

    Thanks David night take you up on the offer and that’s ok ok I’m going to start small anyway so don’t want to get overwhelmed! Hey Rick good to hear you are close by too!
  15. J

    New from Brisbane!

    Hi David, I live at Wakerley so just up the road, I think your house is one of the locations on my list that I want to take a look at this weekend
Top