Media added by Ellis

Navigation

  1. Mini Christmas Expos 270
    1. Mini YouTube videos 74
    2. Mini group photos 196
  2. Display building videos 30
  3. Prop construction photos 51
  4. Behind your show 79
  5. Controller configuration 12
  6. Sequencer tutorials & how-to's 69
    1. xLights videos 33
    2. Vixen videos 36
    3. Other sequencers 0
  7. Miscellaneous 56
Browse albums

Media comments

Most media items

  1. ryanschristmaslights
    233

    ryanschristmaslights

  2. djgra79
    188

    djgra79

  3. Benslights
    136

    Benslights

  4. Roosta
    134

    Roosta

  5. Jase
    102

    Jase

Media statistics

Categories
12
Albums
139
Uploaded media
1,270
Embedded media
366
Comments
219
Disk usage
1 GB
Ellis Christmas Wonderland - Behind the Scenes 2018

Ellis Christmas Wonderland - Behind the Scenes 2018

  • 4
  • 0
Photo 20-6-18, 5 01 57 Pm

Photo 20-6-18, 5 01 57 Pm

  • 3
  • 0
Bunnings Balls 30cm in test mode

Bunnings Balls 30cm in test mode

  • 3
  • 0
Photo 28-1-18, 6 45 42 Pm

Photo 28-1-18, 6 45 42 Pm

  • 0
  • 0
I have used about 20cm or so of Tint tube but other pipe will do

I have used about 20cm or so of Tint tube but other pipe will do

  • 0
  • 0
4 Pixels facing opposing directions to give a circular motion if desired

4 Pixels facing opposing directions to give a circular motion if desired

  • 0
  • 0
This is my 30cm Bunnings Ball conversion

This is my 30cm Bunnings Ball conversion

  • 0
  • 0
Bunnings Balls 20cm in test mode

Bunnings Balls 20cm in test mode

  • 0
  • 0
Top view of finished product

Top view of finished product

  • 0
  • 0
Screw the coro pixel holder in place - remember to loop the adjoining cable behind the screw upright

Screw the coro pixel holder in place - remember to loop the adjoining cable behind the screw upright

  • 0
  • 0
Solder and heatshrink pigtails on - through the base- read notes!

Solder and heatshrink pigtails on - through the base- read notes!

  • 0
  • 0
Cut 1cm in from mark so the join is inside the ball base

Cut 1cm in from mark so the join is inside the ball base

  • 0
  • 0
mark out where pixel cables come out

mark out where pixel cables come out

  • 0
  • 0
check for fit

check for fit

  • 0
  • 0
Cable loop behind the screw upright

Cable loop behind the screw upright

  • 0
  • 0
Insert pixels to coro to line up for fitment

Insert pixels to coro to line up for fitment

  • 0
  • 0
Drill 8mm holes for pigtails - the extra size is to allow for water/condensation drainage

Drill 8mm holes for pigtails - the extra size is to allow for water/condensation drainage

  • 0
  • 0
Mark holes for Pigtails

Mark holes for Pigtails

  • 0
  • 0
Lined up to make sure it fits

Lined up to make sure it fits

  • 0
  • 0
Coro Pixel holder marked and cut out

Coro Pixel holder marked and cut out

  • 0
  • 0
Photo 26-11-17, 9 43 03 Am

Photo 26-11-17, 9 43 03 Am

  • 0
  • 0
Photo 26-11-17, 8 31 16 Am

Photo 26-11-17, 8 31 16 Am

  • 0
  • 0
Photo 26-11-17, 8 30 44 Am

Photo 26-11-17, 8 30 44 Am

  • 0
  • 0
Photo 26-11-17, 8 30 37 Am

Photo 26-11-17, 8 30 37 Am

  • 0
  • 0
Back
Top