[help needed] not all lights are working

Tzdash

New elf
Joined
Oct 3, 2026
Messages
30
If you remember when it was working then can you revert to an older xLights backup? Assuming you've got backups turned on.

It could also help to describe what actually is the problem as it is not clear from your thread title. I.e. what are the lights doing/not doing and what are you expecting them to do?
 
If you remember when it was working then can you revert to an older xLights backup? Assuming you've got backups turned on.

It could also help to describe what actually is the problem as it is not clear from your thread title. I.e. what are the lights doing/not doing and what are you expecting them to do?
I’ve gone through all my backups, none have what I need. I first got it working by pressing the “output to lights” button as I should, now only 1 string works or none
 
I don’t know if this is just a bug @domhodgson , but I’ve found Output to Lights often doesn’t work with the Baldrick 8. So have you tried using xSchedule or whatever scheduling tool you plan to use, just to see if it outputs there?
 
I don’t know if this is just a bug @domhodgson , but I’ve found Output to Lights often doesn’t work with the Baldrick 8. So have you tried using xSchedule or whatever scheduling tool you plan to use, just to see if it outputs there?
So Il save my show and do it through x schedule?
 
I don’t know if this is just a bug @domhodgson , but I’ve found Output to Lights often doesn’t work with the Baldrick 8. So have you tried using xSchedule or whatever scheduling tool you plan to use, just to see if it outputs there?
If you could do Baldrick Buddy help report when this issue is happening I'd love to get this sorted for you as I've not seen this issue listed in our system.
 
I actually haven’t gotten around to using Buddy yet, I’ll have a look when I set up this weekend. I think it could also be something in my FPP proxy though. I was just suggesting in case it was a known error.
 
I actually haven’t gotten around to using Buddy yet, I’ll have a look when I set up this weekend. I think it could also be something in my FPP proxy though. I was just suggesting in case it was a known error.
If you're using proxy, make sure that any time you make changes to your configuration, you do an FPP connect (no sequences) to get the channel config onto the proxy. Also ensure that on the Channel Inputs page of your FPP proxy that the Enable box is ticked.

What happens in proxy mode is xLights sends all channels of proxied controllers as DDP data to FPP. FPP then receives that, goes, oh, that channel belongs to controller X, universe Y (if e1.31) and channel Z, which is reachable over IP address A.B.C.D based on its channel outputs page. It then forwards it through to the controller.

So, if you make changes, and you havent told FPP about those (with FPP Connect) then the proxy wont know where to send the channel data to, even in Output to Lights mode.
 
If you're using proxy, make sure that any time you make changes to your configuration, you do an FPP connect (no sequences) to get the channel config onto the proxy. Also ensure that on the Channel Inputs page of your FPP proxy that the Enable box is ticked.

What happens in proxy mode is xLights sends all channels of proxied controllers as DDP data to FPP. FPP then receives that, goes, oh, that channel belongs to controller X, universe Y (if e1.31) and channel Z, which is reachable over IP address A.B.C.D based on its channel outputs page. It then forwards it through to the controller.

So, if you make changes, and you havent told FPP about those (with FPP Connect) then the proxy wont know where to send the channel data to, even in Output to Lights mode.
So my setup is all I do is I have a working string, I duplicate it, and change the port to a free one. I don’t get what’s wrong with that so it must be a bug
 
So my setup is all I do is I have a working string, I duplicate it, and change the port to a free one. I don’t get what’s wrong with that so it must be a bug
After you do that, are uploading to the controller, and then are you doing an FPP connect? If not, then the proxy doesnt know about the new string.
 
Back
Top