Push Button Speaker Box with Built in FM Receiver - As presented at the Perth 2023 Mini

I’m using the 36v Meanwell to better power the amp I’m using. This amp has a bit more power and the recommended volts was, I believe, 24v-50v.
 
Thanks for your patience!!

Ok. I’m going to get the buck converter and drop down to 12 or even 24. Found this item. https://a.co/d/027SHjCc

I also found this DPDT solid state relay. https://a.co/d/0e0FsZyd

I can override the push button by using this SPDT switch. https://a.co/d/0d8YAFWP

This is the push button relay I found for 36 v. https://a.co/d/0hgDYgcT

Will these products work as you described in your diagram?
This is the timer relay I used https://www.amazon.com/JESSINIE-Tri...delay+timer+control+off+switch,aps,367&sr=8-3
This is the type of relay DPDT that I used with a bit of heatshrink over the connection https://www.jaycar.com.au/12v-dpdt-mini-pcb-relay/p/SY4061

and a up dated diagram
36  v  supply.png
 
Very much appreciated!! Super helpful. I may need to look for a dpdt from a different company. It looks like the one you suggested won’t ship to the United States.
 
Found it! Sure called Latest Buy!
Finally received the dpdt yesterday! Terminals look a bit different from the diagram you posted. Would you be able to help? Here is a pic of the dpdt.
 

Attachments

  • IMG_8274.jpeg
    IMG_8274.jpeg
    714.1 KB · Views: 12
  • IMG_8273.jpeg
    IMG_8273.jpeg
    643.3 KB · Views: 12
Thought I would post some pics of the finished product. Big thanks to Croydon Lights for all the help!!!
 

Attachments

  • IMG_8484.jpeg
    IMG_8484.jpeg
    1.1 MB · Views: 24
  • IMG_8485.jpeg
    IMG_8485.jpeg
    1,017.6 KB · Views: 24
Everything is working but the timer relay gets really hot really quick and then will shut down. Not sure what to troubleshoot. Step down is doing its job going from 36v to 12v. All connections look good. Any thoughts?
 
That'll do it if you are running all the power through the timer. But isn't the timer just activating the DPDT? I am not even an amateur at this kind of thing but you shouldn't have much else connected to the output and would doubt the DPDT switch would need more than 1A to actuate. A 10 amp relay "should" be more than adequate. You might want to check that you don't have a wire tail somewhere or take some actual measurements and see if you are drawing more than expected.
 
Back on this thread! I need to buy a new arcade push button. Any Amazon recommendations?
 
hope this helps
Hi there! You helped me a few months back with my audio push button box. I'm in need of your help again if you are willing! Things were working for a while then stopped. Couldn't get the push button working, had issues with the relay and can't even remember what else. I did a few modifications to the most current diagram you sent me. I now have two power supplies. 1 36V that only powers the amp. I eliminated the step down and am using a second power supply (12V) to power everything else. I replaced my push button with a new one, replaced the time delay relay with a new one and replaced the DPDT that I use turn the speaker wires on and off. All was good a few weeks ago! Working great! Went out there just now to give it a final test before Thanksgiving and not working properly. I believe the problem is in the Single Pole Double Throw switch that I use to either use the push button or to keep constant sound on. I think at this point, I want to eliminate that switch all together and only use the system as the push button. (The issues the switch is having, is sometimes power does not get to the relay, sometimes it does. Sometimes the relay triggers itself without pushing the button.). The on switch has still consistently worked.

My question is this. Could you please tell me the easiest way to update my diagram so that I can just use the push button? Can I just connect the three wires that come together for the SPDT or do I need to do something else?

Thank you so much!
 
Back
Top